Автор Тема: Доступ к сетевым ресурсам Windows в Runtu XFCE 14.04.2 x64  (Прочитано 17524 раз)

0 Пользователей и 1 Гость просматривают эту тему.

Оффлайн nevoplush

  • Прохожий
  • *
  • Автор темы
  • Сообщений: 2
Доброго времени суток.

Вопрос наболевший, очень.
Поставил сборку данную. И ника не могу из неё достучаться до папок на windows машинах.
Чем можно победить? (руки может и не очень кривые, но и не админские - поэтому прошу сильно не кидаться )


Оффлайн and2

  • Постоялец
  • ***
  • Сообщений: 118
Доступ к сетевым ресурсам Windows в Runtu XFCE 14.04.2 x64
« Ответ #1 : Апрель 30, 2015, 04:27:48 »
nevoplush
Для настройки доступа нам потребуется установить (если не установлено) графическую утилиту для настройки system-config-samba.
Командуем в терминале или устанавливаем через центр приложений. В терминале:
sudo apt-get install system-config-sambaЗдесь всё подробно: http://comp.ydoma.info/nastrojka-obshhego-dostupa-papkam-fajlam-kompjuternoj-seti-runtu-xfce-14.04.html

Сначала сделал как написано,всё равно нет полных прав.Разобрался,автор забыл упомянуть,что прежде чем менять права у папки её нужно обязательно сначала Открыть как администратор.
Исправление неправильной кодировки машин с русскими именами в локальной сети.
При открытии в файловом менеджере вкладки "Сеть" видим вместо машин с русскими именами набор символов.
Проблема решается добавлением всего двух строчек в smb.conf
Открываем папку samba от админа (/etc/samba/smb.conf),в текстовом редакторе открываем smb.conf и дописываем после "Browsing/Identification" эти две строчки:dos charset = cp866
usershare owner only = false
Перезагружаемся и видим что теперь компьютеры в локальной сети отображаются нормально.
« Последнее редактирование: Апрель 30, 2015, 09:17:16 от and2 »

Оффлайн HsH

  • Administrator
  • *****
  • Сообщений: 3474

    system-config-samba - утилита для настройки доступа к локальным ресурсам по сети, т.е. чтобы сделать каталоги на текущем ПК видимыми в сетевом окружении. На доступ с локального ПК к другим сетевым ресурсам она не влияет. Центр приложений в дистрибутивах Runtu не устанавливается.

    nevoplush, опишите более подробно, с чем связана ваша проблема и как она проявляется.

Оффлайн nevoplush

  • Прохожий
  • *
  • Автор темы
  • Сообщений: 2
Домашняя сеть.
Несколько компьютеров с windows, с расшаренными папками.
Поставил сборку runtu. Захожу в Файловый менеджер, Сеть, Обзор сети, Сеть Windows - пусто.
Захожу по старой памяти "smb://[pcname]" - "не удалось получить список доступных на сервере ресурсов" ....
Собственно всё...


Оффлайн nicksmith

  • Новичок
  • **
  • Сообщений: 15
И никак не могу из неё достучаться до папок на windows машинах.
Чем можно победить? (руки может и не очень кривые, но и не админские - поэтому прошу сильно не кидаться )
Столкнулся с такой же проблемой, но на второй день после настройки, подсказанной and2. Справился с проблемой изменив настройки на Windows компьютерах. Лишь один комп в WINDOWS сети не трогал, используемый для раздачи Интернет и как общее хранилище. На остальных Winodws компьютерах в службах поотключал следующие службы:
- Обозреватель компьютеров
- Служба сетевого расположения (NLA)
- Служба сетевого DDE
и все компьютеры Windows сети стали видны.
Но вот с тем, что на второй день все Windows компьютеры с русскими именами опять стали писаться "крякозябриками" так и не могу справиться.
Может кто подскажет как поправить?
« Последнее редактирование: Ноябрь 03, 2015, 09:03:05 от nicksmith »

Оффлайн HsH

  • Administrator
  • *****
  • Сообщений: 3474
на второй день все Windows компьютеры с русскими именами опять стали писаться "крякозябриками"

    Приведите содержимое /etc/samba/smb.conf в теге "код" или под спойлером.

Оффлайн nicksmith

  • Новичок
  • **
  • Сообщений: 15
Вот как-то так:
#
# Sample configuration file for the Samba suite for Debian GNU/Linux.
#
#
# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options most of which
# are not shown in this example
#
# Some options that are often worth tuning have been included as
# commented-out examples in this file.
#  - When such options are commented with ";", the proposed setting
#    differs from the default Samba behaviour
#  - When commented with "#", the proposed setting is the default
#    behaviour of Samba but the option is considered important
#    enough to be mentioned here
#
# NOTE: Whenever you modify this file you should run the command
# "testparm" to check that you have not made any basic syntactic
# errors.

[MB#!#======================= Global Settings =======================

[global]

## Browsing/Identification ###
dos charset = cp866
usershare owner only = false
# Change this to the workgroup/NT-domain name your Samba server will part of
   workgroup = XXX

# server string is the equivalent of the NT Description field
   server string = %h server (Samba, Ubuntu)

# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable its WINS Server
#   wins support = no

# WINS Server - Tells the NMBD components of Samba to be a WINS Client
# Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
;   wins server = w.x.y.z

# This will prevent nmbd to search for NetBIOS names through DNS.
   dns proxy = no

#### Networking ####

# The specific set of interfaces / networks to bind to
# This can be either the interface name or an IP address/netmask;
# interface names are normally preferred
;   interfaces = 127.0.0.0/8 eth0

# Only bind to the named interfaces and/or networks; you must use the
# 'interfaces' option above to use this.
# It is recommended that you enable this feature if your Samba machine is
# not protected by a firewall or is a firewall itself.  However, this
# option cannot handle dynamic or non-broadcast interfaces correctly.
;   bind interfaces only = yes



#### Debugging/Accounting ####

# This tells Samba to use a separate log file for each machine
# that connects
   log file = /var/log/samba/log.%m

# Cap the size of the individual log files (in KiB).
   max log size = 1000

# If you want Samba to only log through syslog then set the following
# parameter to 'yes'.
#   syslog only = no

# We want Samba to log a minimum amount of information to syslog. Everything
# should go to /var/log/samba/log.{smbd,nmbd} instead. If you want to log
# through syslog you should set the following parameter to something higher.
   syslog = 0

# Do something sensible when Samba crashes: mail the admin a backtrace
   panic action = /usr/share/samba/panic-action %d


####### Authentication #######

# Server role. Defines in which mode Samba will operate. Possible
# values are "standalone server", "member server", "classic primary
# domain controller", "classic backup domain controller", "active
# directory domain controller".
#
# Most people will want "standalone sever" or "member server".
# Running as "active directory domain controller" will require first
# running "samba-tool domain provision" to wipe databases and create a
# new domain.
   server role = standalone server

# If you are using encrypted passwords, Samba will need to know what
# password database type you are using. 
   passdb backend = tdbsam

   obey pam restrictions = yes

# This boolean parameter controls whether Samba attempts to sync the Unix
# password with the SMB password when the encrypted SMB password in the
# passdb is changed.
   unix password sync = yes

# For Unix password sync to work on a Debian GNU/Linux system, the following
# parameters must be set (thanks to Ian Kahan <<kahan@informatik.tu-muenchen.de> for
# sending the correct chat script for the passwd program in Debian Sarge).
   passwd program = /usr/bin/passwd %u
   passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* .

# This boolean controls whether PAM will be used for password changes
# when requested by an SMB client instead of the program listed in
# 'passwd program'. The default is 'no'.
   pam password change = yes

# This option controls how unsuccessful authentication attempts are mapped
# to anonymous connections
   map to guest = bad user

########## Domains ###########

#
# The following settings only takes effect if 'server role = primary
# classic domain controller', 'server role = backup domain controller'
# or 'domain logons' is set
#

# It specifies the location of the user's
# profile directory from the client point of view) The following
# required a [profiles] share to be setup on the samba server (see
# below)
;   logon path = \\%N\profiles\%U
# Another common choice is storing the profile in the user's home directory
# (this is Samba's default)
#   logon path = \\%N\%U\profile

# The following setting only takes effect if 'domain logons' is set
# It specifies the location of a user's home directory (from the client
# point of view)
;   logon drive = H:
#   logon home = \\%N\%U

# The following setting only takes effect if 'domain logons' is set
# It specifies the script to run during logon. The script must be stored
# in the [netlogon] share
# NOTE: Must be store in 'DOS' file format convention
;   logon script = logon.cmd

# This allows Unix users to be created on the domain controller via the SAMR
# RPC pipe.  The example command creates a user account with a disabled Unix
# password; please adapt to your needs
; add user script = /usr/sbin/adduser --quiet --disabled-password --gecos "" %u

# This allows machine accounts to be created on the domain controller via the
# SAMR RPC pipe. 
# The following assumes a "machines" group exists on the system
; add machine script  = /usr/sbin/useradd -g machines -c "%u machine account" -d /var/lib/samba -s /bin/false %u

# This allows Unix groups to be created on the domain controller via the SAMR
# RPC pipe. 
; add group script = /usr/sbin/addgroup --force-badname %g

############ Misc ############

# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting
;   include = /home/samba/etc/smb.conf.%m

# Some defaults for winbind (make sure you're not using the ranges
# for something else.)
;   idmap uid = 10000-20000
;   idmap gid = 10000-20000
;   template shell = /bin/bash

# Setup usershare options to enable non-root users to share folders
# with the net usershare command.

# Maximum number of usershare. 0 (default) means that usershare is disabled.
;   usershare max shares = 100

# Allow users who've been granted usershare privileges to create
# public shares, not just authenticated ones
   usershare allow guests = yes

#======================= Share Definitions =======================

# Un-comment the following (and tweak the other settings below to suit)
# to enable the default home directory shares. This will share each
# user's home directory as \\server\username
;[homes]
;   comment = Home Directories
;   browseable = no

# By default, the home directories are exported read-only. Change the
# next parameter to 'no' if you want to be able to write to them.
;   read only = yes

# File creation mask is set to 0700 for security reasons. If you want to
# create files with group=rw permissions, set next parameter to 0775.
;   create mask = 0700

# Directory creation mask is set to 0700 for security reasons. If you want to
# create dirs. with group=rw permissions, set next parameter to 0775.
;   directory mask = 0700

# By default, \\server\username shares can be connected to by anyone
# with access to the samba server.
# Un-comment the following parameter to make sure that only "username"
# can connect to \\server\username
# This might need tweaking when using external authentication schemes
;   valid users = %S

# Un-comment the following and create the netlogon directory for Domain Logons
# (you need to configure Samba to act as a domain controller too.)
;[netlogon]
;   comment = Network Logon Service
;   path = /home/samba/netlogon
;   guest ok = yes
;   read only = yes

# Un-comment the following and create the profiles directory to store
# users profiles (see the "logon path" option above)
# (you need to configure Samba to act as a domain controller too.)
# The path below should be writable by all users so that their
# profile directory may be created the first time they log on
;[profiles]
;   comment = Users profiles
;   path = /home/samba/profiles
;   guest ok = no
;   browseable = no
;   create mask = 0600
;   directory mask = 0700

[printers]
   comment = All Printers
   browseable = no
   path = /var/spool/samba
   printable = yes
   guest ok = no
   read only = yes
   create mask = 0700

# Windows clients look for this share name as a source of downloadable
# printer drivers
[print$]
   comment = Printer Drivers
   path = /var/lib/samba/printers
   browseable = yes
   read only = yes
   guest ok = no
# Uncomment to allow remote administration of Windows print drivers.
# You may need to replace 'lpadmin' with the name of the group your
# admin users are members of.
# Please note that you also need to set appropriate Unix permissions
# to the drivers directory for these users to have write rights in it
;   write list = root, @lpadmin

Оффлайн HsH

  • Administrator
  • *****
  • Сообщений: 3474

    nicksmith, если Runtu используется только как клиент (обзор общих каталогов Windows), внести в /etc/samba/smb.conf параметры
dos charset = cp866
display charset = utf8
unix charset = utf8

Что означает
   workgroup = XXXсуществующую группу?

Оффлайн nicksmith

  • Новичок
  • **
  • Сообщений: 15
Что означает
  workgroup = XXXсуществующую группу?
Да, это существующая группа. В файле стояла группа по умолчанию, не помню точно, но вроде WORKGROUP, я вместо нее и поставил имя группы.
А вообще потом хотелось бы чтобы и компьютер на Linux расшарил свою папку для Windows.
Ну да не все сразу, попробую по шагам. Как без перезапуска Linux применить параметры? Перезапуском Samba? (какой командой?)
Есть желание весь офис перевести на Linux, но сразу все настроить не получится. Для начала настроить один комп. Но вопросов, чем дальше продвигаюсь, возникает все больше.

Оффлайн sfs

  • Местный
  • *****
  • Сообщений: 722
    • PuppyRus-Arch
Если просмотр сети не нужен (ип и имя шары известно) - mount.cifs

Оффлайн nicksmith

  • Новичок
  • **
  • Сообщений: 15
Re: Доступ к сетевым ресурсам Windows в Runtu XFCE 14.04.2 x64
« Ответ #10 : Ноябрь 03, 2015, 13:26:54 »
Если просмотр сети не нужен (ип и имя шары известно) - mount.cifs
Пользователи не часто заглядывают в "чужие" папки, более логично выглядит открыть ее в случае необходимости.

Оффлайн and2

  • Постоялец
  • ***
  • Сообщений: 118
Re: Доступ к сетевым ресурсам Windows в Runtu XFCE 14.04.2 x64
« Ответ #11 : Ноябрь 03, 2015, 17:29:09 »
nicksmith
Вот здесь http://forum.runtu.org/index.php/topic,6539.15.html я подробно написал что нужно сделать для расшаривания папок Linux - Windows.Только вот такую нужно сделать поправочку,да,жизнь (и практика) вносит свои поправки.Нужно ОБЯЗАТЕЛЬНО установить system-config-samba (вместе с установкой Samba).У меня после замены smb.conf русские папки не всегда показывались корректно.Нужно после смены как писал smb.conf,запустить system-config-samba и в ней хотя бы снять или поставить любую галочку и нажать ОК.Перезагрузиться.Всё,все имена русских папок будут отображаться корректно.Во всяком случае на Runtu XFCE 14.04 - 20140514 32 бит это так (сейчас она у меня установлена).Видимо должно сработать и на  Runtu XFCE 14.04.2 x64.
В Windows 7 кроме правильных сетевых настроек нужно через твикер разрешить доступ по локалке - Включить общие ресурсы в локальной сети (ADMIN$, C$ и т.д.) и Разрешить анонимным пользователям просматривать учетные записи и расшаренные ресурсы в локальной сети.
Сделать можно это через reg файл.Копируем всё в текстовой файл и называем например Win7.reg,затем запускаем его двойным кликом и соглашаемся с вопросом.Что не нужно можно просто удалить из текстового файла.
Win7.reg
Windows Registry Editor Version 5.00

;Добавление пункта "Открыть в блокноте" в контекстное меню файлов
[HKEY_CLASSES_ROOT\*\shell\Открыть в Блокноте]
@=""
[HKEY_CLASSES_ROOT\*\shell\Открыть в Блокноте\command]
@="notepad.exe %1"

;При отключении флешки индикатор гаснет.
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\usbhub\hubg]
"DisableOnSoftRemove"=dword:00000001

;Включить общие ресурсы в локальной сети (ADMIN$, C$ и т.д.)
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\LanmanServer\Parameters]
"AutoShareWks"=dword:00000001

;Разрешить анонимным пользователям просматривать учетные записи и расшаренные ресурсы в локальной сети.
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Lsa]
"restrictanonymous"=dword:00000000

;Использовать кодовую страницу 1251 вместо 1252, решает проблемы с отображением русских шрифтов в некоторых программах
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Nls\CodePage]
"1250"="c_1251.nls"
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Nls\CodePage]
"1252"="c_1251.nls"
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\FontMapper]
"ARIAL"=dword:000000cc
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\FontSubstitutes]
"MS Sans Serif,0"="MS Sans Serif,204"
"Tahoma,0"="Tahoma,204"
"Arial,0"="Arial,204"
"Courier,0"="Courier New,204"
"Courier,204"="Courier New,204"
"Times New Roman,0"="Times New Roman,204"
"Verdana,0"="Verdana,204"

;Отключить службу Центр обеспечения безопасности (Security Center)
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\wscsvc]
"Start"=dword:00000004

;Отключить службу Центр обновления Windows
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\wuauserv]
"Start"=dword:00000004

;Убрать флажок в трее Центра поддержки
[HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer]
"HideSCAHealth"=dword:00000001

;Настройка контроля учётных записей
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Policies\System]
;Выполнение программ Администратором без запроса
"ConsentPromptBehaviorAdmin"=dword:00000000
;Отключить контроль учётных записей (UAC)
"EnableLUA"=dword:00000000
;Не спрашивать при запуске приложений
"PromptOnSecureDesktop"=dword:00000000

Оффлайн nicksmith

  • Новичок
  • **
  • Сообщений: 15
Re: Доступ к сетевым ресурсам Windows в Runtu XFCE 14.04.2 x64
« Ответ #12 : Ноябрь 11, 2015, 13:55:33 »
nevoplush
Для настройки доступа нам потребуется установить (если не установлено) графическую утилиту для настройки system-config-samba.
Командуем в терминале или устанавливаем через центр приложений. В терминале:
sudo apt-get install system-config-samba
Подскажите чем ваша команда отличается от sudo apt-get install samba gvfs-backends system-config-sambaВ крайний раз использовал эту команду, что она мне добавила, или убавила, по сравнению с вашей?
Спасибо.
« Последнее редактирование: Ноябрь 11, 2015, 14:32:34 от nicksmith »

Оффлайн nicksmith

  • Новичок
  • **
  • Сообщений: 15
Re: Доступ к сетевым ресурсам Windows в Runtu XFCE 14.04.2 x64
« Ответ #13 : Ноябрь 11, 2015, 14:29:59 »
Уважаемый HsH. Долго занимался настройкой Linux компа для работы в Windows сети, стараясь все задокументировать. И когда настроил, как показалось, уже достаточно, решил еще один комп настроить на Linux. Вот тут и казалось что не все записал.
В частности по настройке сетевых принтеров. В 1-ом, настроенном компе окно настройки нового компа выглядит так:

А на 2-ом, настраиваемом компе так:

т.е. нет строки "принтер Windows через SAMBA". И никак не удается вспомнить что еще доустанавливал чтобы оно появилось. Может кто подсказать?
Спасибо.

Оффлайн HsH

  • Administrator
  • *****
  • Сообщений: 3474
Re: Доступ к сетевым ресурсам Windows в Runtu XFCE 14.04.2 x64
« Ответ #14 : Ноябрь 11, 2015, 16:20:01 »
нет строки "принтер Windows через SAMBA".

    По идее, достаточно пакетов smbclient и pyton-smbc.